Pfe 95% / FFP1 / FFP2 N95 Mask Meltblown Filter Melt Blown Non-Woven Fabric
Melt-blown non-woven fabric is a kind of ultrafine fiber non-woven material made by melt-blown process, raw material is food grade PP, fibre diameter can be 0.4um-2um. The product is treated with special electrostatic, characteristics of high efficiency and low resistance, comfortable and easy to adorn. Can effectively filtration and adsorption of microorganisms, viruses and extremely dust.
Medical grade mask filter can meet with Europe standard EN14638:2003 requirements, the bacterial filtration efficiency(BFE) is over 95%. Or China Standard YY 0469-2011.
Industry grade mask filter can meet with Europe standard EN149:2001 +a1:2009 FFP1/FFP2/FFP3 requirements, and USA standard NIOSH 42 CFE-84 requirement such as N95/N99, and China Standard GB 2626-2006 requirement as KN95 etc. Particle filtration efficiency(PFE) is over 95%
With the capability to produce fine fibres, ideally suited for the filtration of respirable particles, Meltblown fabrics provide air filtration applications with excellent barrier and filtration properties.Available in weights ranging from 20 - 80gsm (PP), Meltblown nonwovens are perfectly suited for applications such as industrial respirators, vacuum cleaner bags, automotive cabin filters, and microbiological filters
Advantages:
- Available in widths up to 160 cm
- Available in various colours
- Melt additives to give enhanced fabric properties, such as UV stability and hydrophobicity
- Electrostatic charging of filaments for enhanced sub-micron particle filtration
- In-line measurement and control of air permeability
- In-line thermal flat calendaring
Applications:
Melt Blown Fabric for Face Mask Filter Material:
Melt Blown Face Mask Filter Material is a type of HEPA (high efficiency particulate air) filter. This 100% virgin polypropylene filtration material can be used for PPE (personal protective equipment) masks and respirators. This material has been tested to block 95% of airborne particles with an average particle size range of 0.3 microns (also known as micrometers). Use this material as the filter layer inside a face mask or face respirator. Please note this material is single use only and non-washable. Based on The American Society for Testing and Materials (ASTM) standard, this mask filtration material is rated at ASTM Level 1 (see documents). A Level 1 rating is for Low Fluid Resistance. When this filter material is used as the inner layer of a face mask made from a recommended mask material, such as Spun Bonded Polypropylene Non-Woven Material for Masks, the effectiveness of the mask increases.
Testing & Certifications:
This PFE 95% filtration material has gone through rigorous testing and has passed all required certifications for use as the filter material in masks and respirators for blocking 95% of particles. It has passed the PFE (Particle Filtration Efficiency) Test. This test determines the material's filtration efficiency by passing aerosolized particles through the material at a constant flow rate and fixed air pressure. This test method complies with GB 2626-2006, EN149:2001+a1:2009. Please Note: This filter material has only been tested PFE,not BFE. PFE testing is for particles smaller than those that meet BFE standards. Usually, disposal face mask test on BFE, and N95 mask test on PFE This material has also been tested for breathability and has passed the necessary certification. It was administered and passed the Test, which complies with GB/T32616-2016, EN 14683:2019, Annex C. All test method criteria were met for this material. Testing was performed in compliance with the United States FDA (Food and Drug Administration) good manufacturing practice (GMP) regulations 21 CFR Parts 210, 211 and 820. Test Standard in Different Countries Below:
Product Classifications
|
Countries |
Performance Standard |
| P2, P3 |
Australia/New Zealand |
AS/NZS 1716:2012 |
| PFF2, PFF3 |
Brazil |
ABNT/NBR 13698:2011 |
| KN95, KP95, KN100, KP100 |
China |
GB2626-2006
GB2626-2019
GB19083-2010 |
| FFP2, FFP3 |
Europe |
EN 149-2001 |
| DS/DL2, DS/DL3 |
Japan |
JMHLW-2000 |
| Korea 1st class |
Korea |
KMOEL-2017-64 |
N95, P95, R95
N99, P99, R99
N100, P100, R100 |
Mexico |
NOM-116-20 |
Comparation of Different Grade of Melt Blown Fabric
Factory and Machine:
QINGDAO TAIMEI PRODUCTS CO.,LTD. started tarpaulin business in 2006. And we have three factories to manufacture different covering fabric, including PE and PVC Tarpaulin, Plastic Net, Sun Shade Sail, Woven and Non-Woven Fabric, Plastic Film, Packaging Material, etc. By supplying our goods to different industries such as construction, agriculture, shipping, automobile, logistic, oil field, military industries and retailing , we have more than 10 years experience in different application and 60 different countries including America, Europe, Japan, Middle East, Africa etc. We are committed to produce the best covering products to protect what you cared for and will continue to work hard adding new products to our range. We are very confident that you will enjoy corporation with us.
Audited Supplier 
Audited Supplier 
){kind=link}
){kind=link}